2025 100% Free FCSS_SDW_AR-7.4 Daily Practice Exam With 51 Questions
FCSS_SDW_AR-7.4 exam torrent Fortinet study guide
Fortinet FCSS_SDW_AR-7.4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
NEW QUESTION # 17
Refer to the exhibit.
An administrator is troubleshooting SD-WAN on FortiGate. A device behind branch1_fgt generates traffic to the 10.0.0.0/8 network.
The administrator expects the traffic to match SD-WAN rule ID 1 and be routed over HUB1-VPN1. However, the traffic is routed over HUB1-VPN3.
Based on the output shown in the exhibit, which two reasons, individually or together, could explain the observed behavior? (Choose two.)
- A. HUB1-VPN3 has a higher member configuration priority than HUB1-VPN1.
- B. HUB1-VPN3 has a lower route priority value (higher priority) than HUB1-VPN1.
- C. The traffic matches a regular policy route configured with HUB1-VPN3 as the outgoing device
- D. HUB1-VPN1 does not have a valid route to the destination
Answer: A,B
NEW QUESTION # 18
Refer to the exhibits.
You connect to a device behind a branch FortiGate device and initiate a ping test. The device is part of the LAN subnet and its IP address is 10.0.1.101.
Based on the exhibits, which interface uses branch 1_fgt to steer the test traffic?
- A. port4
- B. port1
- C. port2
- D. HUB1-VPN1
Answer: B
NEW QUESTION # 19
In which SD-WAN template field can you use a metadata variable?
- A. You can use metadata variables only to define interface members and the gateway IP.
- B. Any field identified with an "M" in a circle.
- C. All SD-WAN template fields support metadata variables.
- D. Any field identified with a dollar sign (S) in a magnifying glass.
Answer: B
NEW QUESTION # 20
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows two IPsec templates to define BranchIPsec_1 and Branch_IPsec_2. Each template defines a VPN tunnel.
Exhibit B shows the error message that FortiManager displayed when the administrator tried to assign the second template to the FortiGate device.
Which statement best explain the cause for this issue?
- A. You can define only one IPsec tunnel from branch devices to HUB1.
- B. You should review the branch1_fgt configuration for the already configured tunnel with the name HUB1-VPN2.
- C. You can assign only one template with a tunnel of type static to each FortiGate device.
- D. You can assign only one IPsec template to each FortiGate device.
Answer: D
Explanation:
One Template per FortiGate Device, you have multiple tunnels inside the template.
NEW QUESTION # 21
Refer to the exhibit. The administrator configured the IPsec tunnel VPN1 on a FortiGate device with the parameters shown in exhibit.
Based on the configuration, which three conclusions can you draw about the characteristics and requirements of the VPN tunnel? (Choose three.)
- A. The administrator must manually assign the tunnel interface IP address on the hub side
- B. The remote end must support IKEv2.
- C. The remote end can be a third-party IPsec device.
- D. The tunnel interface IP address on the spoke side is provided by the hub.
- E. This configuration allows user-defined overlay IP addresses.
Answer: A,C,E
NEW QUESTION # 22
When a customer delegate the installation and management of its SD-WAN infrastructure to an MSSP, the MSSP usually keeps the hub within its infrastructure for ease of management and to share costly resources.
In which two situations will the MSSP install the hub in customer premises? (Choose two.)
- A. The customer expects a large amount of VoIP traffic.
- B. The administrator expects a large volume of traffic between the branches.
- C. The majority of the branch traffic is directed to a corporate data center.
- D. The customer requires SIA with centralized breakout.
Answer: B,D
NEW QUESTION # 23
Refer to the exhibits. You connect to a device behind a branch FortiGate device and initiate a ping test. The device is part of the LAN subnet and its IP address is 10.0.1.101.
Based on the exhibits, which interface uses branch 1_fgt to steer the test traffic?
- A. port4
- B. port1
- C. port2
- D. HUB1-VPN1
Answer: B
NEW QUESTION # 24
SD-WAN interacts with many other FortiGate features. Some of them are required to allow SD-WAN to steer the traffic.
Which three configuration elements that you must configure before FortiGate can steer traffic according to SD-WAN rules? (Choose three.)
- A. Routing
- B. Firewall policies
- C. Security profiles
- D. Traffic shaping
- E. Interfaces
Answer: A,B,E
NEW QUESTION # 25
What is true about SD-WAN multiregion topologies?
- A. Each region has its own SD-WAN topology.
- B. Regions must correspond to geographical areas.
- C. Routing between the hub and spokes must be BGP.
- D. It is not compatible with ADVPN.
Answer: A
NEW QUESTION # 26
Exhibit.
Which action will FortiGate take if it detects SD-WAN members as dead?
- A. FoftiGate bounces port5 after it detects all SD-WAN members as dead.
- B. FortiGate sends alert messages through poft5 when it detects all SD-WAN members as dead
- C. FortiGate brings down port5 after it detects all SD-WAN members as dead.
- D. FortiGate fails over to the secondary device after it detects port5 as dead.
Answer: C
NEW QUESTION # 27
Refer to the exhibit. You want to configure SD-WAN on a network as shown in the exhibit. The network contains many FortiGate devices. Some are used as NGFW, and some are installed with extensions such as FortiSwitch, FortiAP or FortiExtender. What should you consider when planning your deployment?
- A. You must use FortiManager to manage your SD-WAN topology.
- B. You can build an SD-WAN topology that includes all devices. The hubs can be FortiGate devices with Forti Extender.
- C. You can build an SD-WAN topology that includes all devices. The hubs must be devices without extensions.
- D. You must build multiple SD-WAN topologies. Each topology must contain only one type of extension.
Answer: C
NEW QUESTION # 28
Which three characteristics apply to provisioning templates available on FortiManager? (Choose three.)
- A. A CLI template group can contain CLI templates of both types.
- B. Each template group can contain up to three IPsec tunnel templates.
- C. A CLI template can be of type CLI script or Perl script.
- D. A template group can include a system template and an SD-WAN template.
- E. CLI templates are applied in order, from top to bottom
Answer: A,D,E
NEW QUESTION # 29
You are planning a large SD-WAN deployment with approximately 1000 spokes and want to allow ADVPN between the spokes. Some remote sites use FortiSASE to connect to the company's SD-WAN hub. Which overlay routing configuration should you use?
- A. BGP on loopback with dynamic BGP for ADVPN shortcut routing.
- B. BGP per overlay with dynamic BGP for ADVPN shortcut routing.
- C. BGP per overlay with BGP next-hop convergence for ADVPN shortcut routing.
- D. BGP on loopback with IPsec phase2 selectors for ADVPN shortcut routing.
Answer: A
NEW QUESTION # 30
You are planning a new SD-WAN deployment with the following criteria:
- Two regions
- Most of the traffic is expected to remain within its region
- No requirement for inter-region ADVPN
To remain within the recommended best practices, which routing protocol should you select for the overlays?
- A. IBGP with BGP per overlays within each region and IBGP with BGP on loopback between the regions.
- B. IBGP with BGP on loopback within each region and EBGP between the regions.
- C. OSPF for the routing within each region and EBGP between the regions.
- D. IBGP within each region and between the regions.
Answer: B
NEW QUESTION # 31
Refer to the exhibits.
The exhibits show the configuration for SD-WAN performance. SD-WAN rule, the application IDs of Facebook and YouTube along with the firewall policy configuration and the underlay zone status.
Which two statements are true about the health and performance of SD-WAN members 3 and 4? (Choose two.)
- A. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
- B. Encrypted traffic is not used for the performance measurement.
- C. Only related TCP traffic is used for performance measurement.
- D. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
Answer: A,C
NEW QUESTION # 32
When you use the command diagnose sys session list, how do you identify the sessions that correspond to traffic steered according to SD-WAN rules?
- A. You identify sessions steered according to SD-WAN rules with the flag vwl.
- B. You cannot identify SD-WAN sessions. You must use the sdwar. session filter.
- C. You identify sessions steered according to SD-WAN rules with the data 3dwan_service_id.
- D. You identify sessions steered according to SD-WAN rules with the data vwl_mbr_seq.
Answer: C
NEW QUESTION # 33
You are tasked with configuring ADVPN 2.0 on an SD-WAN topology already configured for ADVPN. What should you do to implement ADVPN 2.0 in this scenario?
- A. Update the SD-WAN configuration on the branches.
- B. Update the IPsec tunnel configurations on the hub.
- C. Update the IPsec tunnel configuration on the branches.
- D. Delete the existing ADVPN configuration and configure ADVPN 2.0.
Answer: A
NEW QUESTION # 34
Refer to the exhibit. An administrator configures SD-WAN rules for a DIA setup using the FortiGate GUI. The page to configure the source and destination part of the rule looks as shown in the exhibit. The GUI page shows no option to configure an application as the destination of the SD-WAN rule Why?
- A. You cannot use applications as the destination when FortiGate is used for a DIA setup.
- B. FortiGate allows the configuration of applications as the destination of SD-WAN rules only on the CLI.
- C. You must enable the feature first using the GUI menu System > Feature Visibility.
- D. You must enable the feature on the CLI.
Answer: A
NEW QUESTION # 35
Refer to the exhibits. The exhibits show two IPsec templates to define Branch IPsec 1 and Branch_IPsec_2. Each template defines a VPN tunnel. The error message that FortiManager displayed when the administrator tried to assign the second template to the FortiGate device is also shown. Which statement best describes the cause of the issue?
- A. You can assign only one template with a tunnel type of static to each FortiGate device.
- B. You can assign only one IPsec template to each FortiGate device.
- C. You should review the branch1_fgt configuration for configured tunnels in the rootVDOM.
- D. You should use the same outgoing interface of both templates.
Answer: B
NEW QUESTION # 36
You manage an SD-WAN topology. You will soon deploy 50 new branches.
Which three tasks can you do in advance to simplify this deployment? (Choose three.)
- A. Define metadata variables value for each device.
- B. Create policy blueprint.
- C. Update the DHCP server configuration.
- D. Create model devices.
- E. Create a ZTP template.
Answer: B,D,E
NEW QUESTION # 37
Refer to the exhibit. Which action will FortiGate take if it detects SD-WAN members as dead?
- A. FortiGate sends alert messages through poft5 when it detects all SD-WAN members as dead.
- B. FoftiGate bounces port5 after it detects all SD-WAN members as dead.
- C. FortiGate brings down port5 after it detects all SD-WAN members as dead.
- D. FortiGate fails over to the secondary device after it detects port5 as dead.
Answer: C
NEW QUESTION # 38
Refer to the exhibit.Two hub-and-spoke groups are connected through redundant site-to-site IPsec VPNs between Hub 1 and Hub 2.
Which two configuration settings are required for the spoke A1 to establish an ADVPN shortcut with the spoke B2? (Choose two.)
- A. On hubs, auto-diacovery-sender must be enabled on the IPsec VPNs to spokes
- B. On hubs, auto-discovery-forwarder must be enabled on the IPsec VPNs to spokes.
- C. On hubs, auto-discovery-forwarder must be enabled on the IPsec VPNs to hubs.
- D. On hubs, auto-discovery-receiver must be enabled on the IPsec VPNs to spokes.
Answer: A,C
NEW QUESTION # 39
Refer to the exhibit.
An administrator checks the status of an SD-WAN topology using the FortiManager SD-WAN monitor menus. All members are configured with one or two SLAs.
Which two conclusions can you draw from the output shown? (Choose two.)
- A. branch2_fgt establishes six tunnels to the hubs and they are all up.
- B. One member of branch2_fgt is missing the SLAs.
- C. This SD-WAN topology contains only two branch devices.
- D. The template view should be used to see the hub devices.
Answer: B,C
NEW QUESTION # 40
Exhibit.
Refer to the exhibit, which shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured packet loss will make HUB1-VPN3 the new preferred member?
- A. When all three members have the same packet loss
- B. When HUB1-VPN1 has 12% packet loss
- C. When HUB1-VPN1 has 4% packet loss
- D. When HUB1-VPN3 has 4% packet loss
Answer: A
NEW QUESTION # 41
Refer to the exhibits. You use FortiManager to configure SD-WAN on three branch devices.
When you install the device settings. FortiManager prompts you with the error "Copy Failed" for the device branch1_fat When you click the log button. FortiManager displays the message shown in the exhibit.
Based on the exhibits, which statement best describes the issue and how you can resolve it?
- A. Remove the installation target for the SD-WAN member port4. You cannot combine metadata variable and installation targets.
- B. Check the connection between branch1_fgt and FortiManager
- C. Gateways for all members in a zone must be defined the same way. Specify the gateway of the SD- WAN member port! without metadata variables.
- D. Check the metadata variable definitions, and review the per-device mapping configuration.
Answer: A
NEW QUESTION # 42
......
Use Valid New FCSS_SDW_AR-7.4 Test Notes & FCSS_SDW_AR-7.4 Valid Exam Guide: https://www.testvalid.com/FCSS_SDW_AR-7.4-exam-collection.html
FCSS_SDW_AR-7.4 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://drive.google.com/open?id=1VLEqCT3JSE0-WpLfcwUmvi2GzoGRljt6